Antec DF-35 Manuel d'utilisateur

D F-35 DARK FLEET THE ADVANCED GAMING FORCE US E R MA N U A L

10 2.1 SETTING UP Put the case upright on a flat, stable surface so that the rear panel (power supply and expansion slots) is facing you. To remove

11 Now rest your case with the left side up. Here’s what we’ll be working with first: A – Power supply mounts B – 5.25” drive bay area C – 3.5” dr

12 2.2 MOTHERBOARD INSTALLATION Before proceeding: - Check the manual for your CPU cooler to find out if there are steps you must do befor

13 3. Now remove your motherboard by lifting it up. Lift your motherboard out to install the standoffs. 4. Install standoffs as needed and put th

14 Note: The DF-35 comes with a CPU cutout on the motherboard tray, which will allow you to change your CPU heatsink without removing the motherboar

15 Use these screws to secure your power supply to the case. 2.4 CABLE MANAGEMENT There is a cable management compartment behind the 3

16 2.5 INTERNAL 3.5” DEVICE INSTALLATION The DF-35 includes two Fleet-Release™ access doors. With the front bezel facing you, they are l

17 Make sure to install screws on the left side… …as well as the right side. 4. Mount any other 3.5” HDD devices accordingly. 5. Connect the app

18 Insert your drive as shown. 2. With one hand supporting the drive, fasten the drive with the screws provided. 3. Find a small 4-pin white conne

19 A – Fleet-Swap™ SATA and power connectors B – Fleet-Swap™ bay screws 2. You may wish to move the Fleet-Swap bays. There are two screws securing

2 DF-35 USER’S MANUAL Congratulations on your purchase of the Antec Dark Fleet DF-35. The DF-35 is a completely unique chassis – massively convenien

20 One example of AHCI configuration – your motherboard may vary B. LOADING THE FLEET-SWAP BAYS Fleet-Swap™ bays are designed to be accessible fr

21 Open the Fleet-Release Access Door to access the drive you want to unload. 3. Grasp the top and bottom of your HDD. Now pull the HDD free. Remo

22 2.8 USING THE TOP 2.5” HOT-SWAP BAY The DF-35’s top 2.5” hard drive bay is hot-swap capable. To use the hot-swap feature, ensure that y

23 2.9 EXTERNAL 5.25” DEVICE INSTALLATION There are three externally accessible 5.25” drive bays. Before you begin, remove both side pa

24 2.10 INTERNAL 2. 5” DEVICE INSTALLATION There is a 2.5” device mounting location located at the bottom of the case. To use this mount

25 3. FRONT I/O PORTS SECTION 3

26 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Gro

27 3.3 POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS Connected to your front panel are LED and switch leads for power, re

28 COOLING SYSTEM SECTION 4

29 4.1 INCLUDED FANS Standard fans on the DF-35: A –1 x 120 mm rear TwoCool™ LED fan B – 1 x 140 mm top TwoCool™ fan C – 2 x Fleet-Rele

3 TABLE OF CONTENTS SECTION 1: INTRODUCTION 1.1 Getting to know your case…………………………………………………. 5 1.2 Case specifications………………………………………………………….

30 4.2 TOP 140 MM TWOCOOL™ FAN The DF-35 comes with one 140 mm TwoCool™ fan. This fan has a two-speed switch that lets you choose the spe

31 4.4 REAR EXHAUST 120 MM TWOCOOL™ WHITE LED FANS There is one 120 x 25 mm TwoCool™ white LED fan preinstalled at the rear of the case.

32 4.6 WASHABLE AIR FILTERS There is a filter located behind the faceplate of each Fleet-ReleaseTM Access Door. There are total of thr

33 Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterda

4 INTRODUCTION SECTION 1

5 1.1 GETTING TO KNOW YOUR CASE Drive bays Hardware mounts 1 5.25” drive bays 9 Motherboard standof

6 1.2 CASE SPECIFICATIONS CASE TYPE Mid Tower COLOR Matte black DIMENSIONS 19.1″ (H) x 7.8″ (W) x 19.1″ (D) 485 mm (H) x 198 mm (W) x

7 1.3 BEFORE YOU BEGIN In order to ensure that your building experience with the Dark Fleet DF-35 will be a positive one, please take no

8 1.4 LOCATING AND POSITIONING YOUR COMPUTER Your DF-35 has backwards- and top-facing exhaust fans, as well as front-mounted intake fans

9 HARDWARE INSTALLATION SECTION 2